Using the Pull Tractor Unit. Using the Roll Paper Stand. Replacing the Ribbon Cartridge. Cleaning the Housing. General Information. Clearing Paper Jams. Replacement Parts. A note appears like this. It provides additional information which helps you to use and understand the product. An important message appears like this.
It provides supplemental information which can prevent potential problems. A caution message appears like this. It provides information which, if ignored, can result in equipment malfunction or damage. A warning message appears like this. It provides information which, if ignored, can result in the risk of personal injury.
Do not plug the printer into the power outlet until the following steps have been completed. Reach into the top cover slot 1 and remove the access cover. Remove the printhead shipping restraint.
Keep the shipping restraint for future use. When replacing a ribbon cartridge, make sure you have the correct replacement ribbon for your printer. The wrong ribbon will not print when installed in your printer. The ribbon ink can cause permanent stains. Make sure the printer is turned off!
If you are replacing the ribbon cartridge , remove the used one:. Do not remove the ribbon shield 1 from the new ribbon! Unpack the ribbon cartridge and install it on the printhead. Press gently on the ribbon cartridge until you feel it click into place. Turn the take-up knob 1 in the direction of the molded arrow to take up any ribbon slack.
Align the notch 1 with the pin on the platen shaft and push it firmly into place. The head gap is the distance between the printhead and the platen roller. When you use envelopes or multipart forms, you need to have a larger gap than when using plain paper. Use the recommended head gap to ensure the best print quality and easy paper feed. Incorrect setting of the head gap can cause printhead damage or ribbon jams.
Related sponsored items. Showing Slide 1 of 3. New New New. Free shipping Free shipping Free shipping. Seller Report item - opens in a new window or tab. Seller assumes all responsibility for this listing. Item specifics. Compatible Brand:. Computer Trade Exchange ctesales Visit Store: Computer Trade Exchange. Shipping and handling. This item will ship to Germany , but the seller has not specified shipping options. Contact the seller - opens in a new window or tab and request a shipping method to your location.
Shipping cost cannot be calculated. Please enter a valid ZIP Code. No additional import charges at delivery! This item will be shipped through the Global Shipping Program and includes international tracking. Learn more - opens in a new window or tab.
There are 10 items available. Open the printer access cover. Remove the ribbon cartridge 1. Place the head gap adjusting lever 2 to the range 9 position. Remove the printhead 3. Remove the two mounting screws 1. Lift the ribbon guide 2 and remove it. Remove the ribbon guide 3. Lift the ribbon protector 2 and remove it. Disconnect the interface cable 1.
Detach the platen knob 2. Remove the two cover mounting screws 3 at the rear of the printer. Lift the rear access cover 4 to the open position. Remove the upper cover assembly 3. Disconnect the operator panel cable 1 from CN10 2 on the control board. Remove the two mounting screws 3. Detach the operator panel holder 4 by moving it upward, and then pulling toward the front of the printer.
Remove the ribbon cartridge. Release the lock of connector CN10 1 and detach the operator panel cable 2. Remove the five shield cover mounting screws 3. Remove the control board 3. Detach connectors CN 1 and CN 2 from the interface connector board. Remove the three mounting screws 3 at the rear of the printer mechanism 4. Loosen the three 7 mm line feed motor mounting bolts 1. Move the line feed motor 2 closer to the platen 3 and detach the line feed drive belt 4.
Remove the printer mechanism 3. Remove the three mounting bolts and washers 1. Remove the line feed motor 2. NOTE: When installing the line feed motor, the cable should be positioned toward the top. Adjust the line feed belt tension 3. Detach the printhead 3. Work from the bottom of the printer mechanism and loosen the two mounting screws 1.
Detach tabs A and B from the frame and remove the cable holder 2. Raise the front of the printer mechanism. Disconnect cables CN2 1 and CN3 2 from the sensor board 3. Remove the three sensor board mounting screws 4. Remove the two ribbon cartridge bracket mounting screws 1.
Detach the cartridge bracket 2. Detach the ribbon feed assembly 4. NOTE: When assembling, install the ribbon drive assembly so that the gear teeth contact properly 5.
Remove the ribbon feed assembly 3. Loosen the two belt pulley bracket mounting screws 1. While pushing the belt pulley bracket 2 to the left, temporarily tighten the two screws. This will ease the tension on the space belt. Remove the head cable assembly 3.
Remove the space motor assembly 3. Remove the mounting screw 1. Detach the belt clamp 2. Remove the belt pulley 3 from the bracket 4 and detach the space belt 5. Using needle-nosed pliers, detach the nylon cable clamp 3 from the fan cover 4. Disconnect connector CN2 1. Remove the two mounting screws 2. The gears must not bind together. Detach the bail arm springs 1. NOTE: The left bail arm spring is longer than the right bail arm spring. Be sure to install each spring on the proper side.
Loosen the screw 1 and slide it towards the back of the printer. Loosen the mounting screw 2 and detach the left eccentric collar 3.
NOTE: The protrusions on the eccentric collars face the outside of the printer. Remove the two springs 1 located on each side of the paper pressure guide 2. Remove the detent spring 3 located on the release lever at the right side of the printer. Remove the mounting screw to remove the release lever microswitch 1. Push down on the mounting tab and remove the printhead gap microswitch 2.
Remove the lower center guide 1. The adjustment patterns are printed. When adjustment pattern printing is completed, a message appears. Following these instructions place the adjustment patterns on the platen , and press the printer's Start button. Head position adjustment starts. Page top.
0コメント